Gas-powered actuator replaced by manual gearbox at Gasunie

November 4, 2026

For an existing Gasunie installation, Integron replaced a roughly forty-year-old gas-powered actuator with a manual gearbox. Precise measurement and thorough preparation were essential to ensure the new drive would fit the existing valve.

From gas-powered actuator to manual operation

When the function of an installation changes, the required drive may also change. For this Gasunie installation, remote operation was no longer necessary. It was therefore decided to replace the existing gas-powered actuator with a manual gearbox.

On paper, that seems like a relatively simple adjustment. In practice, the conversion required precise preparation. The existing actuator had been in place for about forty years, and the new gearbox had to align exactly with the existing valve and structure.

The challenge for Integron therefore lay not only in replacing the drive, but primarily in delivering a suitable solution within the existing installation.

How do you replace a drive on an existing valve?

For installations that have been in operation for decades, replacing a component is not straightforward. The current situation must first be accurately mapped out before a suitable replacement component can be selected.

The existing installation was therefore carefully measured. Based on this data, Gasunie was able to order the correct gearbox.

This step was essential. The dimensions had to match the existing setup to ensure the new gearbox could be correctly mounted onto the valve. By measuring accurately in advance, the actual conversion could be prepared in a targeted manner.

Careful preparation and safe execution

Work on existing gas installations requires careful preparation. Before starting the work, the necessary safety procedures were followed, and the installation was prepared in accordance with the applicable on-site agreements.

Integron was then able to begin the technical work:

  • careful dismantling of the existing gas-powered actuator;
  • determining the correct position of the valve;
  • installing the new manual gearbox;
  • precise mounting and adjustment of the gearbox;
  • checking the operation after installation.

Experience is particularly important with existing installations. The new drive must not only fit physically, but also work correctly with the existing valve after installation.

Why precise measurement is essential for existing installations

This conversion clearly demonstrates why surveying and measuring an existing installation in advance is so important.

When a component has been part of an installation for decades, it cannot simply be assumed that a new drive can be fitted as a direct replacement. Any discrepancy in the connection or positioning can cause problems and delays during installation.

By carefully documenting the existing situation in advance, Integron and Gasunie were able to prepare for the replacement before the old actuator was removed. This mitigated the technical risk during the actual conversion.

The result: a drive suited to current usage

The conversion has been successfully completed. The old gas-powered actuator has been removed, the manual gearbox has been installed and adjusted, and the operation of the valve has been verified.

The new setup offers a number of concrete benefits:

  • Operation suited to current usage: remote operation was no longer required, allowing for the choice of a manual solution.
  • Simpler drive: the gas-powered actuator has been replaced by a manual gearbox that meets the site's current requirements.
  • Verified operation: after installation and adjustment, the valve was tested to ensure it could be operated correctly.
  • Retention of the existing installation: the existing valve and infrastructure could be retained while the method of operation was adapted.

It is precisely the retention of the existing installation that makes this project interesting. Rather than replacing more than necessary, the drive was adapted to the current operational situation.

Adapting existing installations instead of replacing them entirely

Technical installations often have a long service life. During that lifespan, usage, processes, and technical requirements can change. This does not automatically mean that an entire installation needs to be replaced.

This case study at Gasunie demonstrates that a targeted modification can be a suitable alternative. By first accurately assessing and measuring the existing situation, a new drive could be selected and installed while the existing valve remained in place.

Technical customisation is therefore not just about supplying a new component. It is primarily about understanding what is already there, determining what the installation needs today, and ensuring that old and new components are technically well-integrated.

Technical customisation for actuators and valves

Integron works on the maintenance, inspection, repair and modification of actuators, valves and associated drives. For existing installations, a solution often begins with a thorough assessment of the current technical situation.

This project for Gasunie is a concrete example of this: from surveying and work preparation to dismantling, installation, adjustment and functional testing.

Does your organisation have an existing actuator, valve or drive that needs to be modified or replaced?

Integron will help you find the right technical solution, from inventory and surveying to installation and adjustment.

Get in touch with Integron to discuss the options for your installation.

‍